Assessment of Compressive Strength and Hardness of Al-Gr Composites Produced Using Liquid Homogenization Followed by Cold-Press and SPS

Document Type : Original Articles

Authors

1 Ferdowsi University of Mashhad

2 Ferdowsi University of Mashhad, Mashhad, Iran

Abstract

A relatively new method, homogenization in liquid phase, was used to produce aluminum-matrix composite reinforced by graphite particles. The graphite content was chosen from zero to 4.5wt.% in this study. Composite samples were produced using the mixed powder by two ways: spark plasma sintering and cold-press sintering under different pressure, temperature and time conditions. The specimens’ microstructure was investigated by optical microscopy and scanning electron microscopy. To evaluate the mechanical properties of the samples, compression tests and hardness measurements were performed. According to the results, homogenization in liquid phase method caused significant improvements in the distribution of graphite particles in the matrix. Improved mechanical properties were obtained at 3wt.% graphite. According to the results, the compressive strength of Al-2.5wt.% Gr composite, obtained from this mixing process and cold-press sintering, was increased at least 113.8% compared to the pure aluminum. Moreover, SPS process increased the strength of Al-3wt.% Gr composite to about 206.2%, compared to pure aluminum.

Keywords


  1. Lin J. F., Shih M.G., Chen Y.W., "The tribological performance of 6061 aluminium materials in oil lubricants with EP additives", Wear, Vol. 198, pp. 58-70, (1996).
  2. Rohatgi P.K., Liu Y., Yin M., Barr T., "A surface-analytical study of tribo-deformed aluminum alloy319-%10Vol graphite particle composite", Materials Science and Engineering A, Vol. 123, pp. 213-218, (1990).
  3. Basavara Jappa S., Chandramohan G., Davim J., "Application of Taguchi techniques to study dry sliding wear behavior of metal matrix composites", Materials and Design, Vol. 28, pp. 1393-1398, (2006).
  4. Das S., Parasad S.V., Ramachandran T.R., "Tribology of Al-Si alloy - graphite composites: triboinduced graphite films and the role of silicon morphology", Materials Science and Engineering A, Vol. 138, pp. 123-132, (1991).
  5. Rohatgi P.K., Liu Y., Barr T., "Tribological behavior and surface analysis of tribo-deformed Al alloy-50 pct graphite particle composites", Metallurgical and Materials Transactions A, Vol 22, pp. 1435-1441, (1991).
  6. Yang J.B., Lin C.B., Wang T.C., Chu H.Y., "The tribological characteristics of A356.2 Al alloy/Gr(p) composites", Wear, Vol. 257, pp. 941-952, (2004).
  7. Ibrahim I.A., Mohamed F.A., Lavernia E.J., "Particulate reinforced metal matrix composites-a review", Journal of Materials Science, Vol. 26, pp. 1137-1156, (1991).
  8. Liu H., Rohatgi P.K., "Tribological characteristics of aluminum-50 vol pct graphite composite", Metallurgical and Materials Transactions A, Vol. 22, pp. 151-159, (1993).
  9. Pillai U.T.S., Pal B.C., Satyanarayana K.G., Damodaran A.D., "Fracture behaviour of pressure die-cast aluminium-graphite composites", Journal of Materials Science, Vol. 30, pp. 1455-1461, (1995).
  10. Parasad K., Das S., "The significance of the matrix microstructure on the solid lubrication characteristics of graphite in aluminium alloys", Materials Science and Engineering A, Vol. 144, pp. 229-235, (1991).
  11. Wei J.N., Cheng H.F., Zhang Y.F., Han F.S., Zhou Z.C., Shui J.P., "Effects of macroscopic graphite particulates on the damping behavior of commercially pure aluminum", Materials Science and Engineering A, Vol. 325, pp. 444-453, (2002).
  12. Jha A.K., Prasad S.V., Upadhayaya G.S., "Preparation and properties of 6061 aluminium alloy/graphite composites by PM route", Powder Metallurgy, Vol. 32, pp. 309-313, (1989).
  13. Biswas S., Srinivasa U., Seshan S., Rohatgi P.K., "Cast aluminum-graphite composites for industrial applications", AFS Transactions, Vol. 88, pp. 159-166, (1980).
  14. Torralba J.M., Costa A.E., Velasco F., "PM aluminum matrix composites: an overview", Journal of Materials Processing Technology, Vol. 133, pp. 203-206, (2003).
  15. Latief F.H., Sherif El-Sayed M., "Effects of sintering temperature and graphite addition on the mechanical properties of aluminum", Journal of Industrial and Engineering Chemistry, pp. 2129–2134, (2012).
  16. Flores-Zamora M.I., Estrada-Guel I., Gonzalez-Hernandez J., Miki-Yoshida M., Martınez-Sanchez R., "Aluminum–graphite composite produced by mechanical milling and hot extrusion", Journal of Alloys and Compounds, Vol. 434-435, pp. 518–521, (2007).
  17. Guo M.L., Tsao C.Y.A., "Tribological behavior of self-lubricating Aluminum/SiC/Graphite hybrid composites synthesized by the semi-solid powder densification method", Composite Science and Technology, Vol. 60, No. 1, pp. 65-74, (2000).
  18. Chu H., Liu K., Yeh J., "An insitu composite of A1 (graphite, Al4C3) produced by reciprocating extrusion", Materials Science and Engineering A, Vol. 277, pp. 25-32, (2000).
  19. Estrada-Guel I., Carreno-Gallardo C., Mendoza-Ruiz D.C., Miki-Yoshida M., Rocha-Rangel E., Martinez-Sanchez R., "Graphite nanoparticle dispersion in 7075 aluminum alloy by means of mechanical alloying", Journal of Alloys and Compounds, Vol. 483, No. 1-2, pp. 173–177, (2009).
  20. Lin C.B., Chang R.J., Wang W.P., "A study on process and tribological behavior of Al alloy /Gr(p) composite", Wear, Vol. 217, pp. 167-174, (1998).
  21. Gupta M., Lim S.C., Ng W.B., "Processing, microstructure, and mechanical properties of (A1-Cu)/Cu composites synthesized using partial liquid phase casting process", Materials Science and Technology, Vol. 13, pp. 584-589, (1997).
  22. تفریشی ر.، باباخانی ا.، "بررسی خواص مکانیکی کامپوزیت آلومینیم گرافیت تولید شده به روش متالورژی پودر"، سومین همایش مشترک مهندسان متالورژی ایران، (1388).
  23. Daneshvar Sh., Khoramshahi F., Khademi D., Yavari Mehrabani H., Babakhani A., "Fabrication of Aluminum–Graphite Composites by SPS Method", The 3rd International Conference on Composites: Characterization, Fabrication and Application (CCFA-3)", Tehran, Iran, (2012).
  24. Kuzumaki T., Miyazawa K., Ichinose H., Ito K.J., "Processing of carbon nanotubes aluminium composite", Materials Research, Vol. 13, No. 9, pp. 2445–2449, (1998).
CAPTCHA Image