Journal Of Metallurgical and Materials Engineering

Journal Of Metallurgical and Materials Engineering

Effect of ZrC and nano graphene platelet on the microstructure and mechanical properties of ZrB2 based composite

Document Type : Original Articles

Authors
Milad kheyrolahzadeh 1
zohre balak 2
Mehdi Azizieh 1
Mehdi Shahedi asl 3
1 Department of Materials Science and Engineering, Ahvaz Branch, Islamic Azad University, Ahvaz, Iran.
2 Department of Materials Science and Engineering, Ahvaz Branch, Islamic, Azad University, Ahvaz, Iran.
3 Department of Chemistry, School of Science, Xi'an Jiaotong-Liverpool University.
10.22067/jmme.2024.86458.1141
Abstract
In this research,, in order to investigate the effect of adding ZrC on the microstructure and mechanical properties of ZrB2 composites reinforced with graphene nanoplates (GNP), three composites were sintered through spark plasma sintering (SPS) at a temperature of 1900°C for 7 minutes under a pressure of 40 MPa. The sintering behavior,, microstructure and mechanical properties of the resulting composite were also evaluated. The relative density was measured by the Archimedes method. XRD and EDS analysis were used to check the chemical composition and phase identification. Field emission scanning electron microscope (FE-SEM) was used to evaluate the microstructure (grain size and porosity). Bending strength,, hardness and fracture toughness were determined by three-point bending test,, Macro Vickers and Single Edge Notch Beam (SENB) respectively. The results showed that the presence of GNP alone and together with ZrC increases the relative density significantly (99.7%).In addition, full densification was achieved by adding 10 and 20% by volume of ZrC compared to pure ZrB2 ceramics with a relative density of 81%. The maximum hardness, bending strength and fracture toughness of 25.8 GPa, 597 MPa and 4.9 MPa m0.5 were obtained, respectively, for the ZrB2-GNP composite reinforced with 20% by volume of ZrC
Keywords
ZrB2 ceramic
microstructure
hardness
fracture toughness
spark plasma sintering
Subjects
[1] Z. Balak, M. Zakeri, M. R. Rahimipoor, E. Salahi, M. Azizieh, and H. Kafashan, “Investigation of Effective Parameters on Densification of ZrB2-SiC Based Composites Using Taguchi Method,” Advanced Ceramics Progress, vol. 2, pp. 7-15, 2016. https://doi.org/10.30501/acp.2016.90835
[2] Z. Balak, and M. Zakeri, “Effect of HfB2 on microstructure and mechanical properties of ZrB2–SiC-based composites,” Int. Journal of Refractory Metals and Hard Materials, vol. 54, pp. 127–137, 2016. https://doi.org/10.1016/j.ijrmhm.2015.07.011
[3] Z. Balak, and M. Zakeri, “Application of Taguchi L32 orthogonal design to optimize flexural strength of ZrB2-based composites prepared by spark plasma sintering,” Int. Journal of Refractory Metals and Hard Materials, vol. 55, pp. 58–67, 2016. https://doi.org/10.1016/j.ijrmhm.2015.11.009
[4] X. Zhang, Z. Wang, X. Sun, W. Han, and Ch. Hong, “Changqing Hong, Effect of graphite flake on the mechanical properties of hot pressed ZrB2–SiC ceramics,” Materials Letters, vol. 62, pp. 4360–4362, 2008. https://doi.org/10.1016/j.matlet.2008.07.027
[5] S. Tang, J. Deng, S. Wang, W. Liu, and K. Yang, “Ablation behaviors of ultra-high temperature ceramic composites,” Materials Science and Engineering A, vol. 465, no. 1-2, pp. 1-7, 2007. https://doi.org/10.1016/j.msea.2007.02.040
[6] Y. L. Zhang, Y. M. Zhang, J. C. Han, Y. Y. Han, and W. Yao, “Fabrication of toughened Cf/SiC whisker composites and their mechanical properties,” Materials Letters, vol. 62, no. 17–18, pp 2810-2813, 2008. https://doi.org/10.1016/j.matlet.2008.01.090
[7] Ch. Wei, Zh. Zhang, X. Ma, L. Liu, Y. Wu, D. Li, P. Wang, and X. Duan, “Mechanical and ablation properties of laminated ZrB2-SiC ceramics with Si3N4 whisker interface,” Corrosion Science, vol. 197, pp. 110051, 2022. https://doi.org/10.1016/j.corsci.2021.110051
[8] F. Yang, X. Zhang, J. Han, and Sh. Du, “Characterization of hot-pressed short carbon fiber reinforced ZrB2–SiC ultra-high temperature ceramic composites,” Journal of Alloys and Compounds, vol. 472, no. 1–2, pp. 395-399, 2009. https://doi.org/10.1016/j.jallcom.2008.04.092
[9] M. Mashhadi, H. Khaksari, and S. Safi, “Pressureless sintering behavior and mechanical properties of ZrB2–SiC composites, effect of SiC content and particle size,” Journal of Materials Research and Technology, vol. 4, no. 4,  pp. 416-422, 2015. https://doi.org/10.1016/j.jmrt.2015.02.004
[10] R. Tu, B. Xiao, S. Zhang, Zh. Deng, Q. Li, M. Yang, T. Goto, L. Zhang, and H. Ohmori, “Mechanical, electrical and thermal properties of ZrC-ZrB2-SiC ternary eutectic composites prepared by arc melting,” Journal of the European Ceramic Society,  vol. 38, no .11, pp. 3759-3766, 2018.https://doi.org/10.1016/j.jeurceramsoc.2018.04.028
[11] D. Sciti, S. Guicciardi, and M. Nygren, “Spark plasma sintering and mechanical behaviour of ZrC-based composites,” Scripta Materialia, vol. 59, no. 6, pp. 638-641, 2008. https://doi.org/10.1016/j.scriptamat.2008.05.026
[12] Zh. Liyou, J. Dechang, D. Xiaoming, Y. Zhihua, and Z. Yu, “Low temperature sintering of ZrC–SiC composite,” Journal of Alloys and Compounds, vol. 509, no. 41, pp. 9816-9820, 2011. http://dx.doi.org/10.1016/j.jallcom.2011.08.041
[13] M. Shahriari Asl, and Z. Balak, “Sinterability and flexural strength of monolithic ZrB2: Role of nano‑carbon black and SiC,” Carbon Letters, vol. 33, pp. 1689–1697, 2023. https://doi.org/10.1007/s42823-023-00523-1
[14] Zh. Huang, and L. Wu, “Phase Equilibria Diagrams of High Temperature Non-Oxide Ceramics,” Springer, pp. 117, 2018. https://doi.org/10.1007/978-981-13-0463-7
[15] M. Shahriari Asl, and Z. Balak., “Fabrication and Characterization of ZrB2 Ceramic in Presence of Graphite Platelet and SiC, Silicon, vol. 15, pp. 6911–6919, 2023. https://doi.org/10.1007/s12633-023-02553-w
[16] V. Savari, Z. Balak, and V. Shahedifar, “Combined and alone addition effect of nano carbon black and SiC on the densification and fracture toughness of SPS-sintered ZrB2,” Diamond & Related Materials, vol. 128, pp. 109244, 2022. https://doi.org/10.1016/j.diamond.2022.109244
[17] G. B. Yadhukulakrishnan, S. Karumuri, A. Rahman, R. P. Singh, A. Kaan Kalkan, and S. P. Singh, “Spark plasma sintering of graphene reinforced zirconium diboride ultra-high temperature ceramic composites,” Ceramics International, vol. 39, no. 6, pp. 6637–6646, 2013. https://doi.org/10.1016/j.ceramint.2013.01.101
[18] A. Rezapour, and Z. Balak, “Fracture toughness and hardness investigation in ZrB2–SiC–ZrC composite,” Materials Chemistry and Physics, vol. 241, pp. 122284, 2020. https://doi.org/10.1016/j.matchemphys.2019.122284
[19] Z. Balak, M. Shahedi Asl, M. Azizieh, H. Kafashan, and R. Hayati, “Effect of different additives and open porosity on fracture toughness of ZrB2–SiC-based composites prepared by SPS,” Ceramics International, vol. 43, no. 2, pp. 2209-2220, 2017. https://doi.org/10.1016/j.ceramint.2016.11.005
[20] I. Farahbakhsh, Z. Ahmadi, and M. Shahedi Asl, “Densification, microstructure and mechanical properties of hot pressed ZrB2–SiC ceramic doped with nano-sized carbon black,” Ceramics International, vol. 43, no. 11, pp. 8411–8417, 2017. https://doi.org/10.1016/j.ceramint.2017.03.188
Send comment about this article
Enter Name.
Enter a valid email address.
Enter a vaid affiliation.
Enter comments (At leaset 10 words)
CAPTCHA Image
Enter Security Code Correctly.