Journal Of Metallurgical and Materials Engineering

Journal Of Metallurgical and Materials Engineering

The effect of the rolling process on the properties of materials produced by additive manufacturing (3D printing): a review paper

Document Type : Review Paper

Authors
Seied Meisam Sharif Mosavi
Farshad Nazari
Reza Mosalmani
Department of Mechanical Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
10.22067/jmme.2024.89703.1156
Abstract
The rolling process is one of the common and widely used methods in manufacturing and forming various parts. The rolling process has a significant effect on the mechanical properties and microstructure of materials, which making it important in the manufacturing of products. 3D printing or additive manufacturing is a of the new method in producing parts that allows for the direct creation of parts from digital models. This process is based on creation parts layer by layer and can produce various parts quickly and with high precision. The unique features of additive manufacturing, such as design freedom, no need to dies and auxiliary equipment, and the ability to produce complex and integrated parts, have caught the attention of many industries such as aerospace, oil and gas, marine and automotive industries to use this method. In the other hand, problems such as microstructure defects, distortion, residual stress and anisotropy of mechanical properties are among the challenges in additive manufactured or 3D printed parts. Using the rolling process to modify 3D printed parts is one way to improve the microstructure and mechanical properties of materials. By combining the rolling process with additive manufacturing, hardness, strength, and elongation can be increased by homogenizing and refining grains of the structure. Also, this process can reduce distortion and residual stress in the additive manufactured parts.
Keywords
Rolling process
3D printing
Additive manufacturing
Mechanical properties
Microstructure
Residual stress
Subjects
[1] Y. Zhi, X. Wang, S. Wang, X. Liu, "A review on the rolling technology of shape flat products" The International Journal of Advanced Manufacturing Technology, vol. 94, pp. 4507-4518, (2018). https://doi.org/10.1007/s00170-017-1004-8.
[2] J. G. Lenard, Primer on flat rolling. Newnes, (2013). [E-book] Available: Google e-book.
[3] W. J. Kim, J. B. Lee, W. Y. Kim, H. T. Jeong, and H. G. Jeong, "Microstructure and mechanical properties of Mg–Al–Zn alloy sheets severely deformed by asymmetrical rolling" Scripta Materialia, vol. 56, no. 4, pp. 309-312, (2007).
[4]   W. Kim, J. Park, and W. Kim, "Effect of differential speed rolling on microstructure and mechanical properties of an AZ91 magnesium alloy" Journal of Alloys and Compounds, vol. 460, no. 1-2, pp. 289-293, (2008). https://doi.org/10.1016/j.jallcom.2007.06.050.
[5]   W. J. Kim, S. J. Yoo, J. Lee, "Microstructure and mechanical properties of pure Ti processed by high-ratio differential speed rolling at room temperature" Scripta Materialia, vol. 62, no. 7, pp. 451-454, (2010). https://doi.org/10.1016/j.scriptamat.2009.12.008.
[6]   J. Jiang, Y. Ding, F. Zuo, and A. Shan, "Mechanical properties and microstructures of ultrafine-grained pure aluminum by asymmetric rolling" Scripta Materialia, vol. 60, no. 10, pp. 905-908, (2009). https://doi.org/10.1016/j.scriptamat.2009.02.016.
[7]   Z. Li, L. Fu, B. Fu, A. Shan, "Effects of annealing on microstructure and mechanical properties of nano-grained titanium produced by combination of asymmetric and symmetric rolling" Materials Science and Engineering: A, vol. 558, pp. 309-318, (2012). https://doi.org/10.1016/j.msea.2012.08.005.
[8]   X. Huang, K. Suzuki, N. Saito, "Microstructure and mechanical properties of AZ80 magnesium alloy sheet processed by differential speed rolling" Materials Science and Engineering: A, vol. 508, no. 1-2, pp. 226-233, (2009). https://doi.org/10.1016/j.msea.2008.12.052.
[9]   M. John, et al. and P. L. Menezes, "Ultrasonic surface rolling process: Properties, characterization, and applications" Applied Sciences, vol. 11, no. 22, p. 10986, (2021). https://doi.org/10.3390/app112210986.
[10] N. D. Stepanov, A. V. Kuznetsov, G. A. Salishchev, G. I. Raab, and R. Z.  Valiev, "Effect of cold rolling on microstructure and mechanical properties of copper subjected to ECAP with various numbers of passes" Materials Science and Engineering: A, vol. 554, pp. 105-115, (2012). https://doi.org/10.1016/j.msea.2012.06.022.
[11] S. Kheiri, H. Mirzadeh,  M. Naghizadeh, "Tailoring the microstructure and mechanical properties of AISI 316L austenitic stainless steel via cold rolling and reversion annealing" Materials Science and Engineering: A, vol. 759, pp. 90-96, (2019). https://doi.org/10.1016/j.msea.2019.05.028.
[12] R. Ran, et al. and G. D. Wang, "Microstructure, precipitates and mechanical properties of Inconel718 alloy produced by two-stage cold rolling method" Materials Science and Engineering: A, vol. 793, p. 139860, (2020). https://doi.org/10.1016/j.msea.2020.139860.
[13] C. Chen, J. Chen, H. Yan, B. Su, M. Song, S. Zhu, "Dynamic precipitation, microstructure and mechanical properties of Mg-5Zn-1Mn alloy sheets prepared by high strain-rate rolling" Materials & Design, vol. 100, pp. 58-66, (2016). https://doi.org/10.1016/j.matdes.2016.03.129.
[14] L. He, Y. Liu, J. Li, B. Li, "Effects of hot rolling and titanium content on the microstructure and mechanical properties of high boron Fe–B alloys" Materials & Design (1980-2015), vol. 36, pp. 88-93, (2012). https://doi.org/10.1016/j.matdes.2011.10.043.
[15] B. Wang, X. H. Chen, F. S. Pan, J. J. Mao, Y. Fang, "Effects of cold rolling and heat treatment on microstructure and mechanical properties of AA 5052 aluminum alloy" Transactions of Nonferrous Metals Society of China, vol. 25, no. 8, pp. 2481-2489, (2015). https://doi.org/10.1016/S1003-6326(15)63866-3.
[16] A. Hedayati, A. Najafizadeh, A. Kermanpur, F. Forouzan, "The effect of cold rolling regime on microstructure and mechanical properties of AISI 304L stainless steel" Journal of Materials Processing Technology, vol. 210, no. 8, pp. 1017-1022, (2010). https://doi.org/10.1016/j.jmatprotec.2010.02.010.
[17] S. K. Panigrahi and R. Jayaganthan, "Effect of rolling temperature on microstructure and mechanical properties of 6063 Al alloy" Materials Science and Engineering: A, vol. 492, no. 1-2, pp. 300-305, (2008). https://doi.org/10.1016/j.msea.2008.03.029.
[18] M. Jahazi and B. Egbali, "The influence of hot rolling parameters on the microstructure and mechanical properties of an ultra-high strength steel" Journal of materials processing technology, vol. 103, no. 2, pp. 276-279, (2000). https://doi.org/10.1016/S0924-0136(00)00474-X.
[19] L. Van Long, D. Van Hien, N. T. Thanh, N. C. Tho, V. T. Do, "Impact of Cold‐Rolling and Heat Treatment on Mechanical Properties of Dual‐Phase Treated Low Carbon Steel" Advances in Materials Science and Engineering, vol. 2020, no. 1, p. 1674837, (2020). https://doi.org/10.1155/2020/1674837.
[20] H. Zhang, D. Ruia, Y. Xiea, G. Wangb, "Study on Metamorphic Rolling Mechanism for Metal Hybrid Additive Manufacturing", (2013). Available: https://hdl.handle.net/2152/88490.
[21] T. A. Rodrigues, V. Duarte, R. Miranda, T. G. Santos, J. Oliveira, "Current status and perspectives on wire and arc additive manufacturing (WAAM)" Materials, vol. 12, no. 7, p. 1121, (2019). https://doi.org/10.3390/ma12071121.
[22] D. Michl, B. Sydow, M. Bambach, "Ring rolling of pre-forms made by wire-arc additive manufacturing" Procedia Manufacturing, vol. 47, pp. 342-348, (2020). https://doi.org/10.1016/j.promfg.2020.04.275.
[23] R. Xie, Y. Shi, R. Hou, H. Liu, and S. Chen, "Efficient depositing aluminum alloy using thick strips through severe deformation-based friction rolling additive manufacturing: processing, microstructure, and mechanical properties" Journal of Materials Research and Technology, vol. 24, pp. 3788-3801, (2023). https://doi.org/10.1016/j.jmrt.2023.04.075.
[24] F. Martina, et al. and M. Hofmann, "Residual stress of as-deposited and rolled wire+arc additive manufacturing Ti–6Al–4V components" Materials Science and Technology, vol. 32, no. 14, pp. 1439-1448, (2016). https://doi.org/10.1080/02670836.2016.1142704.
[25] J. Gu, B. Cong, J. Ding, S. W. Williams,  Y. Zhai, "Wire+ arc additive manufacturing of aluminum" Conference Proceedings and Journals,(2014). Available: https://hdl.handle.net/2152/88764.
[26] F. Martina, P. A. Colegrove, S. W. Williams, J. Meyer, "Microstructure of interpass rolled wire+ arc additive manufacturing Ti-6Al-4V components" Metallurgical and Materials Transactions A, vol. 46, no. 12, pp. 6103-6118, (2015).https://doi.org/10.1007/s11661-015-3172-1.
[27] B. Wu, Z. Pan, et al. and J. Norrish, "A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement" Journal of Manufacturing Processes, vol. 35, pp. 127-139, (2018). https://doi.org/10.1016/j.jmapro.2018.08.001.
[28] A. Gisario, M. Kazarian, F. Martina, M. Mehrpouya, "Metal additive manufacturing in the commercial aviation industry: A review" Journal of Manufacturing Systems, vol. 53, pp. 124-149, (2019). https://doi.org/10.1016/j.jmsy.2019.08.005.
[29] X. Qiu, et al and T. Y. Xiong, "In-situ Sip/A380 alloy nano/micro composite formation through cold spray additive manufacturing and subsequent hot rolling treatment: microstructure and mechanical properties" Journal of Alloys and Compounds, vol. 780, pp. 597-606, (2019). https://doi.org/10.1016/j.jallcom.2018.11.399.
[30] E. Maleki, S. Bagherifard, M. Bandini, M. Guagliano, "Surface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities" Additive Manufacturing, vol. 37, p. 101619, (2021). https://doi.org/10.1016/j.addma.2020.101619.
[31] G. Marinelli, F. Martina, S. Ganguly, S. Williams, "Grain refinement in an unalloyed tantalum structure by combining Wire+ Arc additive manufacturing and vertical cold rolling" Additive Manufacturing, vol. 32, p. 101009, (2020). https://doi.org/10.1016/j.addma.2019.101009.
[32] A. V. Nemani, M. Ghaffari, A. Nasiri, "Comparison of microstructural characteristics and mechanical properties of shipbuilding steel plates fabricated by conventional rolling versus wire arc additive manufacturing" Additive Manufacturing, vol. 32, p. 101086, (2020). https://doi.org/10.1016/j.addma.2020.101086.
[33] Y. Gao et al., "Towards superior fatigue crack growth resistance of TC4-DT alloy by in-situ rolled wire-arc additive manufacturing" Journal of Materials Research and Technology, vol. 15, pp. 1395-1407, (2021). https://doi.org/10.1016/j.jmrt.2021.08.152.
[34] S. W. Williams, F. Martina, A. C. Addison, J. Ding, G. Pardal, P. Colegrove, "Wire+ arc additive manufacturing" Materials science and technology, vol. 32, no. 7, pp. 641-647, (2016). https://doi.org/10.1179/1743284715Y.0000000073.
[35] J. R. Hönnige, P. A. Colegrove, S. Ganguly, E. Eimer, S. Kabra, S. Williams, "Control of residual stress and distortion in aluminium wire+ arc additive manufacture with rolling" Additive Manufacturing, vol. 22, pp. 775-783, (2018). https://doi.org/10.1016/j.addma.2018.06.015.
[36] V. Gornyakov, Y. Sun, J. Ding, and S. Williams, "Modelling and optimising hybrid process of wire arc additive manufacturing and high-pressure rolling" Materials & Design, vol. 223, p. 111121, (2022). https://doi.org/10.1016/j.matdes.2022.111121.
[37] G. Çam, "Prospects of producing aluminum parts by wire arc additive manufacturing (WAAM)" Materials Today, vol. 62, no. 1, pp. 77-85, (2022). https://doi.org/10.1016/j.matpr.2022.02.137.
[38] Z. Zhao, et al. and T. Xiong, "Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing" Materials & design, vol. 185, p. 108249, (2020). https://doi.org/10.1016/j.matdes.2019.108249.
[39] D. Meyer and N. Wielki, "Internal reinforced domains by intermediate deep rolling in additive manufacturing" CIRP Annals, vol. 68, no. 1, pp. 579-582, (2019). https://doi.org/10.1016/j.cirp.2019.04.012.
Send comment about this article
Enter Name.
Enter a valid email address.
Enter a vaid affiliation.
Enter comments (At leaset 10 words)
CAPTCHA Image
Enter Security Code Correctly.