Production and Characterization of an Aluminum Based Nanocomposite Reinforced With Particles from the Al-Zr System by Means of Mechanical Alloying Process

Document Type : Original Articles

Author

Yazd University, Yazd, Iran

Abstract

In this study, an aluminum matrix nanocomposite reinforced with oxide nanoparticles as well as intermetallic particles in the Al-Zr system was produced and optimized through mechanical milling. Results revealed that even long milling times of the powder mixture would not lead to the production of intermetallic phases in the Al-Zr system. This is while Al3Zr and Al2O3 phases form during subsequent heat treatment after milling by the implementation of the relevant reactions between the powder mixture components. After cold pressing and sintering, the hardness increased to 98 HV due to the presence of Al3Zr and Al2O3 phases. In addition, the wear resistance of the bulk samples decreased significantly.

Keywords


1. Miracle, D.B., “Metal Matrix Composites–from Science to Technological Significance”,,Compos. Sci. Technol., Vol. 65, pp. 2526-2540, (2005).
2. Ozdemir , I., Ahrens S., Mucklich S., Wielage B., “Nanocrystalline Al–Al2O3p and SiCp Composites Produced by High-Energy Ball Milling”, J. Mater. Process. Technol., Vol. 205, pp. 111-118,(2008).
3. Brandes , E.A., Brook G.B., “Smithells Light Metals HandBook”,, Utterworth-Heinemann, Oxford, (1998).
4. Williamson, K., Hall W.H., “X-ray Line Broadening from Field Aluminium and Wolfram”, Acta Metall., Vol.10, pp. 31-210, (1953).
5. Markmann, J., Yamakov, V., Weissmuller, J., “Validating Grain Size Analysis from X-ray Line Broadening: A Virtual Experiment”, Scr. Mater., Vol..59, pp 15-18, (2008).
6. Suryanarayana , C., “Mechanical Alloying and Milling”, Prog. Mater Sci., Vol. 46, pp. 1-184,(2001).
7. Akacs, L., “Self-Sustaining Reactions Induced by Ball Milling”, Prog. Mater Sci., Vol. 47, pp. 355-414,(2002).
8. Botta, W.J., Tomasi, R., Pallone, E.M.J.A., Yavari, A.R“., Nanostructured Composites Obtained by Reactive Milling”, Scr. Mater., Vol. 44, pp. 1735-1740,. (2001)
9. Smolyakov, V.K., Lapshin, O.V., Boldyrev, V.V., “Macroscopic theory of mechanochemical synthesis in heterogeneous systems”, Int. J. Self Propag. High Temp. Synth., Vol. 16, pp. 1-11,. (2007)
10. Butyagin, P., “Mechanochemical Synthesis: Mechanical and Chemical Factors”, J. Mater. Synth. Process. Vol. 8, pp. 205-211,(2007) .
11. Kommel, L., Kimmari, E., “Solid phase’s transformations in boron carbide based composites during heat treatment”, Solid State Phenomena, Vol. 138, pp. 175-180, (2008)
12. Witkin, D.B., Lavernia, E.J., “Synthesis and mechanical behavior of nanostructured materials via cryomilling”, Prog. Mater Sci., Vol. 51, pp. 1-60, (2006).
13. Xun, Y., Lavernia, E.J., Mohamed, F.A., “Synthesis of nanocrystalline Zn-22 Pct Al using cryomilling”, Metall. Mater. Trans. A, Vol. 35, pp. 573-581, (2004).
14. Enayati, M.H., Aryanpour, G.R., Ebnonnasir , A“., Production of Nanostructured WC–Co powder by ball milling”, Int. J. Refract. Met. Hard Mat., Vol. 27, pp. 159-163, (2009)
15. Hegue Zhu, Jing Min, “In Situ fabrication of (Al2O+Al3Zr)/Al composites in an Al-ZrO2 system,” Nanjing, PR China, (2010).
16. Hasan, S., Panjepour, M., Shamanian, M., Ghaei , A., “A Tension Analysis During Oxidation of Pure Aluminum Powder Particles: Non-isothermal Condition,” Oxidation of Metals. Vol.82, pp.209-224, (2014)
17. Hasani S., Panjepour M., Shamanian M., “Non-Isothermal Kinetic Analysis of Oxidation of Pure Aluminum Powder Particles” , Oxidation of Metals. Vol.81, pp.299-313, (2014).
18. Hasani, S., Panjepour, M., Shamanian , M ,. “The Oxidation Mechanism of Pure Aluminum Powder Particles”, Oxidation of Metals. Vol.78, pp.179-195, (2012)
19. German, R.A., “Sintering Theory and Practice”, John Wiley & Sons Inc., New York, (1996).
20. Fang , F., Agrawal, D.K., Roy, R., Angerer, P., Skandan , G., “The Microwave Sintering of Nano-phase MgO, TiO2 and Cu Metal Powders”, Proceedings in Sintering , Penn State University, Pennsylvania, USA, (2003).
21. Panda S.S., Upadhyaya A., Agrawal D, “Microwave Sintering of Aluminum Alloys”, J. Mater. Sci.,Vol. 42, pp. 966-978, (2007).
22. Rahimian, M., Parvin, N., Ehsani, N., “Investigation of Particle Size and Amount of Alumina on Microstructure and Mechanical Properties of Al Matrix Composite Made by Powder Metallurgy”, Materials Science and Engineering A, Vol. 527, pp. 1038-1031, (2010)
23. Dieter, G.E., “Mechanical Metallurgy”, third edition, McGraw-Hill, (1976).
24. Gwidon S., “Wear: Materials, Mechanisms and Technology”, John wiley, New York, (2005)
25. Miyajima T., Iwai Y., “Effects of Reinforcements on Sliding Wear Behavior of Aluminum Matrix Composites”, Wear, Vol. 255(1-6), pp.606-616, (2003).
CAPTCHA Image