Experimental Investigation Thermal and Mechanical Behavior of Ni/Al Reactive Composites Synthesized by Mechanical Alloying

Document Type : Original Articles

Authors

1 Assistant Professor, University Complex of Materials and Manufacturing Technologies, Malek Ashtar University of Technology (MUT), Tehran, Tehran, Iran

2 University Complex of Materials and Manufacturing Technologies, Malek Ashtar University of Technology (MUT), Tehran, Tehran, Iran

Abstract

Reactive composites are a new group of composite materials consisting of two or more metal materials that can not ignite or explode in the environment but can release a lot of energy due to shock and severe impact loads. This study aimed to investigate the effect of the ratio of constituent particles on the microstructure and thermal and mechanical properties of the Al-Ni composite. For this purpose, the Al-Ni compound with 2:1, 1:1 and 3:1 molar ratios was milled and mixed. Then the samples were cold pressed and sintered at 400 ˚C under argon atmosphere for one hour. The microstructure of samples was analyzed by microstructure field emission scanning electron microscopy (FESEM) and XRD. For the investigation of thermal and mechanical properties, DTA and ignition tests and compression and Hopkinson tests were used respectively. In the ignition test, due to the AlNi product, the highest value of heat released was related to a sample with 1:1 Al:Ni molar ratio. In the compression and Hopkinson tests, the highest values of compressive strength were 208.7 and 309.7 Mpa respectively, which belong to a 1:1 Al:Ni molar ratio. Also, the results showed that the compressive strength increased by changing the strain rate from 0.01 s-1 (in the pressure test) to 1000 s-1 (in the Hopkinson test).

Keywords

Main Subjects


  1. Totten, G. E., MacKenzie, D. S., "Handbook of Aluminum: Vol. 1: Physical Metallurgy and Processes", CRC press, (2003).
  2. Arpatappeh, F. A., Azghan, M. A. and Eslami-Farsani, R., "The Effect of Stacking Sequence of Basalt and Kevlar Fibers on the Charpy Impact Behavior of Hybrid Composites and Fiber Metal Laminates", Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 234, No. 16, pp. 3270-3279, (2020).
  3. Xiong, W., Zhang, X., Tan, M., Liu, C. and Wu, X., "The energy release characteristics of shock-induced chemical reaction of Al/Ni composites", The Journal of Physical Chemistry C, 120, pp. 24551-24559, (2016).
  4. Sun, T., Y. Zheng, Y., Yuan, Y. and H. Wang, H., "Impact-Initiation Sensitivity of High-Temperature PTFE-Al-W Reactive Materials", Crystals, Vol. 12, pp. 30-40, (2022).
  5. Evans, A., San Marchi, C., and Mortensen, A., "Metal matrix composites in Metal Matrix Composites in Industry", Springer, pp. 9-38, (2003).
  6. Wu, J. X., Fang, X., Gao, Z. R., Wang, H. X., Huang, J. Y., Wu, S. Z. and Li, Y.C., "Investigation on Mechanical Properties and Reaction Characteristics of Al-PTFE Composites with Different Al Particle Size", Advances in Materials Science and Engineering, 2018, pp. 10-18, (2018).
  7. Jung, S.H., Lee, K., "Effect of Microstructure Control on Reaction Characteristics in Al/Ni Reactive Powder", The 4th Research and Development Institute-2nd Directorate, Daejeon, 34060, Korea, (2017).
  8. Ren, H., Liu, X., and Ning, J., "Microstructure and mechanical properties of W-Zr reactive materials", Materials Science and Engineering: A, 660, pp. 205-212, (2016).
  9. Huang, J., Fang, X., Li, Y., Wu, J., Song, J., "Mechanical and reaction properties of PTFE/Al/MnO2 reactive materials at different strain rates", Mater, Vol. 7, pp. 50-58, (2018).
  10. Wu, J. X., Fang, X., Gao, Z. R., Wang, H. X., Huang, J. Y., Wu, S. Z. and Li, Y.C., "Investigation on Mechanical Properties and Reaction Characteristics of Al-PTFE Composites with Different Al Particle Size", Advances in Materials Science and Engineering, 2018, pp. 10-18, (2018).
  11. Hadjiafxenti, A., Gunduz, I. E., Tsotsos, C., Kyratsi, T., Doumanidis, C. C. and Rebholz, C., "Synthesis of Reactive Al/Ni Structures by Ball Milling", Intermetallics, 18, No. 11, pp. 2219-2223, (2010).
  12. Benjamin, S, "Mechanical alloying—A perspective", Metal powder report, Vol. 45, Pp. 122-127, (1990).
  13. Yadav, T. P., Yadav, R. M. and Singh, D. P., "Mechanical milling: a top down approach for the synthesis of nanomaterials and nanocomposites", Nanoscience and Nanotechnology, 2, pp. 22-48, (2012).
  14. Florez-Zamora, M., "Comparative study of Al-Ni-Mo alloys obtained by mechanical alloying in different ball mills", Adv. Mater. Sci, Vol. 18, Pp. 301-304, (2008).
  15. Hadjiafxenti, A., Gunduz, I., Kyratsi, T., Doumanidis, C. and Rebholz, C., "Exothermic Reaction Characteristics of Continuously Ball-Milled Al/Ni Powder Compacts", Vacuum, 96, pp. 73-78, (2013).
  16. Huang, C., Chen, J., Bai, , Li, S., Tang, Y., Liu, X. and Ye, Y., "Enhancement of Energy Release Performance of Al–Ni Composites by Adding CuO", Journal of Alloys and Compounds, Vol. 835, pp. 155-271, (2020).
  17. Naiborodenko, Y. S., Itin, V., Belozerov B. and Ushakov, V., "Phases and reactive-diffusion kinetics for mixed Al-Ni powders", Soviet Physics Journal, 16, pp. 1507-1511, (1973).
  18. White, J. D., Reeves, R. V., Son, S. F. and Mukasyan, A. S., "Thermal explosion in Al− Ni system: influence of mechanical activation", The Journal of Physical Chemistry A, 113, pp. 13541-13547, (2009).
  19. Gasparyan, A. and Shteinberg, A., "Macrokinetics of reaction and thermal explosion in Ni and Al powder mixtures", Combustion, Explosion and Shock Waves, 24, pp. 324-330, (1988).
  20. Herbold, E. B., Jordan, J. L. and Thadhani, N., "Effects of processing and powder size on microstructure and reactivity in arrested reactive milled Al+ Ni", Acta materialia, 59, pp. 6717-6728, (2011).
  21. Gunduz, I. E., Fadenberger, K., Kokonou, M., Rebholz, C. and Doumanidis, C. C., "Investigations on the self propagating reactions of nickel and aluminum multilayered foils", Applied Physics Letters, 93, pp. 134101, (2008).
  22. Gunduz, I. E., Fadenberger, K., Kokonou, M., Rebholz, C., Doumanidis C. C. and Ando, T., "Modeling of the self-propagating reactions of nickel and aluminum multilayered foils", Journal of Applied Physics, 105, pp. 074903, (2009).
  23. Peng, J., Chen, Y., Yuan, B. and Jin, C., "A study of impact energy release mechanism and reactive characteristic of Ni-Al-W reactive material fragments", Journal of Physics: Conference Series, 1507, pp. 26-32, (2020).

 

 

 

CAPTCHA Image