Microstructural Evolution during Friction Stir Welding of Austenitic Stainless Steel AISI 316 to Low Carbon Steel St 37

Document Type : Original Articles

Authors

Isfahan University of Technology

Abstract

The microstructural evolution of dissimilar joining of austenitic stainless steel AISI 316 and low carbon steel St37 by friction stir welding has been investigated. Friction stir welding was carried out using a rotational speed of 600 rpm and a linear speed of 50 mm/min. The microstructure was characterized using a scanning electron microscope and optical microscopy. Also, possible phase transformations were determined using X-ray diffraction technique & electron diffraction spectroscopy. The results of phase investigations showed that no carbides and brittle phases were detected at the joined boundary. Microstructural investigations showed that the highest decrease in grain size occurred in the stir zone of the austenitic stainless steel which was attributed to discontinuous dynamic recrystallization caused by severe deformation imposed at high temperatures in this region.

Keywords


1. Celik, A., Alsaran, A., "Mechanical and Structural Properties of Similar and Dissimilar Steel Joints", Materials Characterization, Vol. 43, pp. 311-318, (1999).
2. Lippold, J.C., Kotecki, D.J., "Welding Metallurgy and Weldability of Stainless Steels", Wiley-Interscience, (2005).
3. Arivazhagan, N., Singh, S., Prakash, S., Reddy, G.M., "Investigation on AISI 304 Austenitic Stainless Steel to AISI 4140 low Alloy Steel Dissimilar Joints by Gas Tungsten Arc, Electron Beam and Friction Welding", Materials & Design, Vol. 32, pp. 3036-3050, (2011).
4. Marashi, P., Pouranvari M., Amirabdollahian S., Abedi A., Goodarzi M., "Microstructure and Failure Behavior of Dissimilar Resistance Spot Welds Between low Carbon Galvanized and Austenitic Stainless Steels", Materials Science and Engineering A, Vol. 480, pp. 175-180, (2008).
5. Torkamany, M.J., Sabbaghzadeh J., Hamedi M.J., "Effect of Laser Welding Mode on the Microstructure and Mechanical Performance of Dissimilar Laser Spot Welds Between Low Carbon and Austenitic Stainless Steels", Materials & Design, Vol. 34, pp. 666-672, (2012).
6. Mishra, R.S., Ma Z.Y., "Friction Stir Welding and Processing", Materials Science and Engineering R, Vol. 50, pp. 1-78, (2005).
7. Thomas, W.M., Threadgill,P.L., Nicholas E.D., "Feasibility of Friction Stir Welding Steel", Science and Technology of Welding & Joining, Vol. 4, pp. 365-372, (1999).
8. Fazel-Najafabadi, M., Kashani-Bozorg S.F., Zarei-Hanzaki A., "Joining of CP-Ti to 304 stainless steel using friction stir welding technique", Materials & Design, Vol. 31, pp. 4800-4807, (2010).
9. Fazel-Najafabadi, M., Kashani-Bozorg, S.F., Zarei-Hanzaki A., "Dissimilar lap joining of 304 stainless steel to CP-Ti employing friction stir welding", Materials & Design, Vol. 32, pp. 1824-1832, (2011).
10. Watanabe, T., Takayama, H., Yanagisawa, A., "Joining of aluminum alloy to steel by friction stir welding", Journal of Materials Processing Technology, Vol. 178, pp. 342-349, (2006).
11. Jafarzadegan, M., Feng, A.H., Abdollah-zadeh, A., Saeid, T., Shen, J., Assadi, H., "Microstructural Characterization in Dissimilar Friction Stir Welding Between 304 Stainless Steel and st37 Steel", Materials Characterization, Vol. 74, pp. 28-41, (2012).
12. Chung, Y.D., Fujii, H., Sun, Y., Tanigawa, H., "Interface Microstructure Evolution of Dissimilar Friction Stir butt Welded F82H Steel and SUS304", Materials Science and Engineering: A, Vol. 528, pp. 5812-5821, (2011).
13. Bang, H., Bang, H., Jeon, G., Oh , I., Ro, C., “Gas Tungsten Arc Welding Assisted Hybrid Friction Stir Welding of Dissimilar Materials Al6061-T6 Aluminum Alloy and STS304 Stainless Steel”, Materials & Design, Vol. 37, pp. 48-55, (2012).
14. Kurt, B., “The Interface Morphology of Diffusion Bonded Dissimilar Stainless Steel and Medium Carbon Steel Couples”, Journal of Materials Processing Technology, Vol. 190, pp. 138-141, (2007).
15. Hascalik, A., Unal E., Ozdemir, N., “Fatigue Behaviour of AISI 304 steel to AISI 4340 Steel Welded by Friction Welding”, Journal of Materials Science, Vol. 41, pp. 3233-3239, (2006).
16. Lienert, T. J., Grimmett, B.B., Warke, R.W., “Friction Stir Welding Studies on Mild Steel”, Welding Journal, Vol., pp. 1-9, (2003).
17. Park, S.H.C., Sato, Y.S., Kokawa, H., Okamoto, K., Hirano, S., Inagaki, M., “Microstructural Characterisation of Stir Zone Containing Residual Ferrite in Friction Stir Welded 304 Austenitic Stainless Steel”, Science and Technology of Welding and Joining, Vol. 10, pp. 550-556, (2005).
18. Kou S., "Welding metallurgy", Cambridge Univ Press, (2002).
19. Park, S.H.C., Sato Y.S., Kokawa H., Okamoto, K., Hirano, S., Inagaki, M., “Rapid Formation of the Sigma Phase in 304 Stainless Steel During Friction Stir Welding”, Scripta Materialia, Vol. 49, pp. 1175-1180, (2003).
20. Rollett, A., Humphreys, F.J., Rohrer, G.S., "Recrystallization and Related Annealing Phenomena", Elsevier Science, (2004).
21. Saeid, T., Abdollah-zadeh, A., Assadi, H., Malek, Ghaini F., “Effect of Friction Stir Welding Speed on the Microstructure and Mechanical Properties of a Duplex Stainless Steel”, Materials Science and Engineering: A, Vol. 496, pp. 262-268, (2008).
CAPTCHA Image