Surface improvement of AZ31 magnesium alloy for engineering applications

Document Type : Original Article

Author

• Farzad Soleymani

Faculty member of Payam Noor University. Tehran - Iran.

10.22067/jmme.2023.79359.1083

Abstract

The main purpose of the present study is to apply micro-spark oxidation coating on AZ31 alloy to improve corrosion resistance, bioactivity and biocompatibility of this alloy. The results of the electrochemical impedance test show the improved corrosion resistance of the AZ31 alloy. X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and elemental analysis by X-ray energy (EDS) tests were used to examine the samples. Body simulation fluid (SBF) test was used to evaluate the ability to form apatite on the samples. The results show that the formation of an apatite layer on the surface of the samples can be considered as a measure of bioactivity. Be the right choice for bone implants In the 19th century, at the same time as the Industrial Revolution, the use of metals as implants in the body was developed. The first use of metal implants in the body to repair broken bones was reported. Metal implants are widely used in orthopedic surgery in both temporary and permanent forms. Today, metals have wider applications in orthopedic and dental surgeries. Only a small number of them are biocompatible and are used as implants. Among these magnesium metals and their alloys due to their close properties to bone, release of magnesium ions into bone and its biodegradability. In the simulated body environment, it has been widely considered as temporary implants in medical and orthopedic applications.

Keywords

• Anodized
• Coating
• Mg alloy. Temporary
• bone

Main Subjects

• Biomaterials

---

References

 

[1]   Ghorbanian, L., Emadi, R., Razavi, S. M., Shin, H., Teimouri, A., "Fabrication and characterization of novel diopside/silk fibroin nanocomposite scaffolds for potential application in maxillaofacial bone regeneration", International Journal of Biological Macromolecules, Vol. 58, pp. 275-280, 2013.

[2]   Christenson, E. M., Ansecth, K. S., Bcuckcn, J. J. V. D., Chan, C. K., Ercan, B., Jansen, J. A., Laurencin, C. T., Li, W. J., Murugan, R., Nair, L. S., Ramakrishna, S., Tuan, R. S., "Nanobiomaterials application in orthopedics", Journal of Orthopedic Research, Vol. 25, pp. 11-22, 2006.

 [3] Katti K. S., "Biomaterials in total joint replacement", Colloids and Surfaces B: Biointerfaces, Vol. 39, pp. 133-142, 2004.

[4]   Saini, M., Singh, Y., Arora, P., Arora, V., and Jain, K., "Implant biomaterials: comprehensive review", World Journal of Clinical Cases: WJCC, Vol. 3, pp. 52, 2015.

[5]   Zomorodian, A., Garcia, M. P., Moura e Silva, T., Fernandes, J., Fernandes, M. H., Montemor, M. F., "Corrosion resistance of a composite polymeric coating applied on biodegradable AZ31 magnesium alloy", Acta Biomaterialia, Vol. 9, pp. 8660–8670, 2013.

[6]   Bian, D., Zhou, W., Deng, J., Liu, Y., Li, W., Chu, X., "Development of magnesium-based biodegradable metals with dietary trace element germanium as orthopaedic implant applications", Acta biomaterialia, Vol. 64, pp. 421-436, 2017.

[7]    Chen, Y., Xu, Z., Smith, C., and Sankar, J., "Recent advances on the development of magnesium alloys for biodegradable implants", Acta biomaterialia, Vol. 10, pp. 4561-4573, 2014.

[8]    Najeeb, S., Khurshid, Z., Matinlinna, J. P., Siddiqui, F., Nassani, M. Z., and Baroudi, K., "Nanomodified peek dental implants: Bioactive composites and surface modification—A review", International journal of dentistry, Vol. 2015, 2015.

[9]    Surmenev, R. A., Surmeneva, M. A. and Ivanova, A. A., "Significance of calcium phosphate coatings for the enhancement of new bone osteogenesis–A review", Acta biomaterialia, Vol. 10, pp. 557-579, 2014.

[10] Wong, H. M., Yeung, K. W., Lam, K. O., Tam, V., Chu, P. K., Luk, K. D., et al., "A biodegradable polymer-based coating to control the performance of magnesium alloy orthopaedic implants", Biomaterials, Vol. 31, pp. 2084-2096, 2010.

 [11] Arifvianto, B., Zhou, J., "Fabrication of metallic biomedical scaffolds with the space holder method: a review", Materials, Vol. 7, pp. 3588-3622, 2014.

[12] Razavi, M., Fathi, M.H., Savabi, O., Vashaee, D., Tayebi, L., "In vitro study of nanostructured diopside coating on Mg alloy orthopedic implants", Materials Science and Engineering C, Vol. 41, pp. 168–177, 2014.

[13] Gu, X. N., Zheng, W., Cheng, Y., Zheng, Y.F., "A study on alkaline heat treated Mg–Ca alloy for the control of the biocorrosion rate", Acta Biomateralia, Vol. 5, pp. 2790–2799, 2009.  

[14] Wu, C., Wen, Z., Dai, C., Lu, Y. and Yang, F., "Fabrication of calcium phosphate/chitosan coatings on AZ91D magnesium alloy with a novel method", Surface and Coatings Technology, Vol. 204, pp. 3336–3347, 2010.

[15] Pozzo, L. d. Y., da Conceição, T. F., Spinelli, A., Scharnagl, N. and Pires, A. T., "Chitosan coatings crosslinked with genipin for corrosion protection of AZ31 magnesium alloy sheets", Carbohydrate polymers, Vol. 181, pp. 71-77, 2018.

[16] Tiyyagura, H., Fuchs-Godec, R.,  Gorgieva, S., "Biomimetic gelatine coating for less-corrosive and surface bioactive Mg–9Al–1Zn alloys", Journal of material research, Vol. 33, pp. 1449-1462, 2018.

[17] Chen, Q. Z., Thompson, I. D., Boccaccini, A. R., "45S5 Bioglass-derived glass-ceramic scaffolds for bone tissue engineering", Biomaterials, Vol. 27, pp. 2414-2425, 2006.